نوشته شده توسط : lily

Shutdown Operation

The Engine Electronic Fuel System will shutdown on the actuation on any one of the following:
– Emergency Stop (E-kill)
– Engine Overspeed (10-15% over max. Engine no load speed)
– High Engine Coolant Temperature (225 deg F)
– High Exhaust Gas Temperature (379 deg F)
– Low Engine Lube Oil Pressure (below 20 Psi)

Stopping the Engine
(1). Standard shutdowns not involving hazardous conditions will be performed by pressing the Engine Stop button.
(2). Emergency shutdown is achieved by pressing the Emergency Stop button.
→The Emergency Stop is activated via the red mushroom shaped button on the Engine control panel. The system operates by closing the Engine air intake flap (Air Shutoff Valve) and directly disabling the fuel injection circuit (Injection Disabled). Read More: Injection Disabled on Status Flags Caterpillar ET Software.

#Graphed Parameters:
→Engine Speed
→Air Intake Shutoff Position (Off)
→User Shutdown (On)
(3). Automatic shutdown is by:
a). Engine Overspeed

#Graphed Parameters:
→Engine Speed
→Air Intake Shutoff Position (Off)
→Active Event Codes Present (SPN 190 – FMI 0)

→The safety system is calibrated to the Engine’s normal maximum speed. If this figure is subsequently exceeded by 10-15%, the Engine will be shutdown by closing the air inlet valve (Air Shutoff Valve) and removing the fuel supply to the Fuel Injectors through the ECM (Injection Disabled).
→To verify Overspeed shutdown system operation, push in the OS Verify button for a moment. The Engine must shutdown at 75% or more of Overspeed setting. Read More: How to Setting or Testing the Engine Overspeed using Caterpillar ET Software?
→Monitoring System – Engine Overspeed

b). High Engine Coolant Temperature

#Graphed Parameters:
→Engine Speed
→Engine Coolant Temperature (Set: 170 deg F)
→Active Event Codes Present (SPN 110 – FMI 0)

→Over temperature input is monitored by the ECM, if exceeded the pre-set/trip point, the Engine will be shutdown by removing the fuel supply to the Fuel Injectors. Read More: Event Codes: High Engine Coolant Temperature Warning (SPN 110 – FMI 15).
→Monitoring System – High Engine Coolant Temperature

c). High Exhaust Gas Temperature. Read More: Auxiliary Temperature Sensor – Voltage Above Normal (Diagnostic Code: SPN 441 – FMI 3).

#Graphed Parameters:
→Engine Speed
→Auxiliary Temperature (Set: 160 deg F)
→Active Event Codes Present (SPN 441 – FMI 0)

→Monitoring System – High Auxiliary Temperature

d). Low Engine Lube Oil Pressure

#Graphed Parameters:
→Engine Speed
→Engine Oil Pressure (Set: 12 Psi)
→Active Event Codes Present (SPN 100 – FMI 1)

→Low oil lubricating pressure also monitored by the ECM, if exceeded the pre-set/trip point, the Engine will be shutdown by removing the fuel supply to the Fuel Injectors. Read More: Oil Pressure Voltage High – Diagnostic Code: SPN 100 – FMI 3 (On-Highway Trucks).
→Monitoring System – Low Engine Oil Pressure

 



:: بازدید از این مطلب : 222
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : دو شنبه 22 اسفند 1401 | نظرات ()
نوشته شده توسط : lily

Here is an instruction show you guide on how to perform firmware update for Xentry diagnosis VCI.

Steps:
Firmware update of the XENTRY Diagnosis VCI may be required after updating the diagnosis computer.
This is displayed to you via a pop-up message. Firmware status information is also displayed in the VCI Manager:
Click the “Update” menu item in the VCI Manager. Click on the “Start update” button.

When executing the update, please ensure that the USB connection between diagnosis computer and VCI is not interrupted:

Confirm by clicking on “OK”. The firmware update of the XENTRY Diagnosis VCI will start now.

You will receive a message after executing the firmware update:

Click on “OK”. Coupling between the diagnosis computer and VCI is confirmed in the next window.
You can continue to work with XENTRY Diagnostics Open Shell as usual.



:: بازدید از این مطلب : 232
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : پنج شنبه 18 اسفند 1401 | نظرات ()
نوشته شده توسط : lily

Test feedback today: New Range Rover Sport P300 (L494) year 2018 successfully added the smart key with original JLR DoIP VCI Pathfinder interface. The real JLR DoIP VCI costs $1300 more. You might get a vxdiag JLR DoIP (less than $600 with HDD) that will do the same job.


If you want to know more about Jaguar and Land Rover Diagnostic Tools, please visit https://www.obd2tool.com



:: برچسب‌ها: JLR DoIP VCI ,
:: بازدید از این مطلب : 220
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : جمعه 28 بهمن 1401 | نظرات ()
نوشته شده توسط : lily

If you are looking for a cheap j2534 programmer that works for many brands, check 2022 top 3 j2534 passthru devices below.

  VXDIAG VCX SE SVCI J2534 Godiag J2534
Image
Software Ford IDS

 

Mazda IDS

Toyota Techstream

JLR SDD

Honda HDS

Subaru SSM3/SSM4

Benz Xentry

Volvo VIDA

BMW ISTA

VAG ODIS

Pcmflash

Forscan

PCMHumer

Ford IDS

 

Mazda IDS

Toyota Techstream

Land Rover/Jaguar SDD

ScanMaster-ELM V2.4.12
PCMSCAN V2.1
ELMconfig
Forscan
FOCCCUS
FF2

Honda HDS

 

Ford IDS

Mazda IDS

Toyota Techstream

Forscan

ODIS

pcmflash

ELMConfig, Forscan, ScanMaster

Volvo VIDA

GM GDS2

Operating system Windows 7/ 8/10/11, 32/64bit  Win7 64bit, Win 8, Win 10 Windows 8/10/11, 32/64bit 

 

(Don’t work on Win7)

J2534 passthru Yes Yes Yes
Online Module Programming Yes, need online account, Ford, GM, Honda, Toyota etc online programming tested ok Yes, need online account. Only Ford/Mazda online programming tested ok No tested
License Customize license No No
Firmware update Update online No No
Software update Update by link (except Benz and BMW thru HDD/SSD) Update by Link Update by Link
Ford trucks 12 V 1998-2006 with PWM protocol ( F series supported) Not working on some F series pre-2010 Yes Unknown
Price $159 $129 $29.99

In sum:

1). Speed
VXDIAG VCX SE is quick. This is unbelievably fast comparing with SVCI J2534.
The SVCI is also not bad, but VCX SE is 6 or 7 times much faster than virtual machine if you run the clone from vcm2.

2). Stability
VXDIAG VCX SE is more stable than STIC j2534 when used as Ford/Mazda j2534 passthru device.

3).
VCX SE supports much more brands then SVCI and Godiag. STIC and Godiag does not have Benz and BMW optional license, VXDIAG does.

4). VXDIAG software is always kept up-to-date. The VCX is compatible with Ford IDS V128 and without change date. The SVCI with red housing only can make it working with old loader and V125, I have to install it in date 05-05-2022 , and make a batch file to change to that time so it works and don’t expire.

5).Godiag cannot be used as j2534 passthru for online programming so it is a fraction of VCX and SVCI price.
For diagnostic purposes and DIYers, godiag j2534 is a good start.
For programming, better choose vxdiag vcx se.



:: برچسب‌ها: VXDIAG VCX SE ,
:: بازدید از این مطلب : 201
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : چهار شنبه 19 بهمن 1401 | نظرات ()
نوشته شده توسط : lily

VOCOM II Though vs. VOCOM II Mini

Item Name VOCOM II Tough VOCOM II Mini
Picture  
Computer operating system Windows 10 (32/64 bit) Windows 10 (32/64 bit)
Computer connection USB or Wi-Fi Wi-Fi
Wi-Fi support IEEE 802.11 a/b/g/n IEEE 802.11 a/b/g/n
2.4 Ghz and 5 Ghz 2.4 Ghz and 5 Ghz
Wi-Fi security PSK, EAP-PEAP, EAP-TLS PSK, EAP-PEAP, EAP-TLS
WPA or WPA2 WPA or WPA2
Diagnostic application interfaces RP1210C, J2534, J2534-1 RP1210C, J2534, J2534-1
Vehicle battery 12V or 24V 12V or 24V
Vehicle electronic architecture Legacy Version 2
Version 2 Version 3
Version 3 Version 4 T1
Version 4 T1  
Version 4 T2  
Vehicle connection OBD2, 9-Pin, 6-Pin, FCI, MEFI, BNA* OBD2, 9-Pin*
*using OBD2 adapter
Vehicle interfaces 2xCAN (max. 1 Mbps) 2xCAN (max. 1 Mbps)
1xJ1708 (max. 115 Kbps) 1xJ1708 (max. 38 Kbps)
1xK-Line (max. 115 Kbps)  
1xEthernet (max. 100 Mbps)  
Vehicle communication protocols ISO 11898 ISO 11898
ISO 15765-2 ISO 15765-2
SAE J1939 SAE J1939
SAE J1708 SAE J1708
ISO 13400-2  
ISO 9141  
KWP 2000  
Knorr/Wabco ABS  
NIRA EDC1  
Volvo Penta MEFI  
BOSCH EDC  
J1708 DIS  
Geartronic  
SL2Q/Free Running  
Operating voltage 6V to 32V (max. 36V) 6V to 32V (max. 36V)
Operating temperature -40°C to +85°C -40°C to +70°C
-40°F to +185°F -40°F to +158°F
IP protection rating IP67 IP44
Weight 400 grams 85 grams
14.1 ounces 3 ounces
Dimensions (WxDxH) 160mm x 91mm x 44mm 110mm x 47mm x 22mm
6.30in x 3.58in x 1.73in 4.33in x 1.85in x 0.86in


:: بازدید از این مطلب : 216
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : شنبه 8 بهمن 1401 | نظرات ()
نوشته شده توسط : lily

Xtool tablets (Xtool D8, D9 Pro, A80/H6 Pro etc) are good at VAG MQB 2014- VDO cluster mileage correction. Here is an example of VW Polo 2014.6. Only continental and VDO clusters are supported.

Original odometer: 231419km

Select Special Function->Instrument Cluster->VW->Polo->MQB(2014.06-)
Turn on ignition switch, but don’t start engine.





It read VIN.

It read mileage. It is the same as it is on the cluster.

Press Modify mileage
Input mileage you desired, i.e 63000 km
Put smart key close to the sensing area, click OK to continue

The instrument cluster will turn black. It is normal.

Writing mileage in process


Mileage correction is done.

Check new mileage.

 

 



:: بازدید از این مطلب : 212
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : سه شنبه 20 دی 1401 | نظرات ()
نوشته شده توسط : lily

Always some buyer use the Chrysler Diagnostic Tool, it will appear the registration message, what should be done?

The one thing you need to do is click it off, and works offline.




Other question when you use this tool, please contact us:
https://www.obd2tool.com/category-224-b0-Chrysler+Diagnostic+Tools.html



:: برچسب‌ها: Chrysler Diagnostic Tool ,
:: بازدید از این مطلب : 225
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : پنج شنبه 1 دی 1401 | نظرات ()
نوشته شده توسط : lily

What is JCB ServiceMaster 4?
JCB ServiceMaster 4 is diagnostic software, which contains complete information for diagnostics and calibration of agricultural machinery and engines company JCB. Setting a diagnostic program JCB ServiceMaster 4 on personal computer users have access to view a variety of information, including information that is stored on one DVD.

JCB ServiceMaster 4 Support Language:
English, Italian, German, French

JCB ServiceMaster 4 Functions List:
– Troubleshooting;
– Standard Test service;
– View and edit generated data;
– ECU Flash files with the correct data

JCB ServiceMaster 4 Support Constructions & Agricultural:
Construction:
Backhoe Loaders
Compact Backhoe Loaders
Excavators
Compact Excavators (Mini / Midi)
Telescopic Handlers (2007-, 2007+, Tier4, 525-60 Compacr Loadall)
Skid Steer Loaders (Robot, Skid Steer Loaders and Compacr Track Loaders, Skid Steer Loaders India)
Teletruk (Tier4)
Wheeled Loading Shovels (Compact, Medium, Large, Telemasters)
Articulated Dump Trucks
Vibratory Compactors (Tier3, Interim Tier4, VMT380/430)
Rough Terrain Forklifts (Tier2/3 RTFL, Tier4 RTFL)

Agricultural:
Fastrac Tractors (2000-3000, 3000 Series 2, 3000 Series 3, 3000 Series 4, 4000 Series, 7000 Series, 8250 Series 1, 8250 Series 2, 8000 Series 3)
Telescopic Handlers (2007-, 2007+, Tier4, 525-60 Compacr Loadall)
Wheeled Loading Shovels (Compact, Medium, Large, Telemasters)

Waste:
Telescopic Handlers (Tier3, Tier4)
Wheeled Loading Shovels (427/437/435S T4F, 457 T4F)

Other:
JS Range, JZ70, Backhoe Loader, Loadall 2007-, Loadall 2007+, Loadall Agri Extras, Loadall Construction extras, Robot, Teletruk, Midi Excavator 801-8065, 8080-8085, Dump Truck, Large Wheel Loading Shovels, Compact Wheel Loading Shovels, Fastrac 2000-3000 Series, Fastrac 3000 Series 2, Fastrac 8250 Series 1, Fastrac 8250 Series 2, Fastrac 7000 Series 1, Vibromax, JCB Dieselmax Engine, JCB Engine (IPU OEM), JCB Engine (Base Engine OEM), JCB Generators, LiveLink I, LiveLink II.

JCB ServiceMaser 4 Requirements:
Windows XP 32 bit, Windows 7 32 bit, Wnidows 7 64 bit, Windows 8/8.1 32 bit, Windows 8/8.1 64 bit, Windows 10 32 bit, Windows 10 64 bit
– CPU: Pentium/Athlon 2 GHz or higher
– RAM: 512 MB of system memory
– Hard Drive: 25 GB of available space
– Optical Drive: DVD-ROM

JCB ServiceMaster 4 Download:
https://www.obd2tool.com/goods-4451-JCB-Electronic-Service-Tool-JCB-Diagnostic-Interface.html

How to install guide here:
How to Install JCB ServiceMaster 4 v22.1.2 2022 on Win7/Win10

JCB ServiceMaster 4 v1.45.3 [11.2015] Multilanguage:
http://nitroflare.com/view/5A835A7BFE49498/JCB.ServiceMaster.4.v1.45.3.part1.rar
http://nitroflare.com/view/A73DECB27688EF2/JCB.ServiceMaster.4.v1.45.3.part2.rar
http://nitroflare.com/view/4CF3A719762A143/JCB.ServiceMaster.4.v1.45.3.part3.rar
http://nitroflare.com/view/AFD32669E3C5289/JCB.ServiceMaster.4.v1.45.3.part4.rar

JCB ServiceMaster 4 v1.73.3 [09.2018] Diagnostic Full:
https://mega.nz/#F!TE41nYoI



:: برچسب‌ها: JCB ServiceMaster 4 ,
:: بازدید از این مطلب : 213
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : شنبه 26 آذر 1401 | نظرات ()
نوشته شده توسط : lily

Problem with Xhorse VVDI Key Tool Plus : when reading / writing key for Benz via IR, got message “Device points is less than 10: insufficient points, please go to Update Center to synchronize your device and try this function again!”

Xhorse-VVDI-Key-Tool-Plus-“insufficient-points”Solution

Working solution:

Go to Update——> Device Synchronization——> once device resyncs try the Read again.

The Charge Points are just Use Actuations that need to be recharge as often as possible especially if you use the device a lot. Think about it as a VVDI2 resyncing to the Server every 30 days.

Finally Fixed!



:: برچسب‌ها: Xhorse VVDI Key Tool Plus ,
:: بازدید از این مطلب : 192
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : یک شنبه 1 خرداد 1401 | نظرات ()
نوشته شده توسط : lily

Autel Maxisys Ultra 是 MK908P / MS908P / Elite / MS909 / MS919 的更新版本。它是一款一体式综合扫描仪,具有 5 合 1 VCMI、高级编程和编码功能以及 36 种以上大型维修车间的服务功能,支持市场上 99.99% 品牌的更广泛车辆覆盖(无 IP 限制)。特别是,它支持一些新的 2021 和 2022 车型,包括 GM、Toyota、VW、JLR、Nissan 和 BMW。

通用汽车:

*   Adds ECU Information, Read Codes, Erase Codes, Live Data, Active Test, and Special Function for 33 models in 2022 including Cadillac CT4, Buick Envision, and Chevrolet Blazer.
*   Adds 5 hot special functions: Automatic Start/Stop, Transport Mode, A/C, Rain/Light Sensor, and EGR.
Autel-MaxiSys-Ultra-Great-Upgrade-1
Autel-MaxiSys-Ultra-Great-Upgrade-2
Autel-MaxiSys-Ultra-Great-Upgrade-3

Toyota:

*   Adds basic functions for 41 models in 2021 (including Yaris, and 4Runner), and 9 models in 2022 (including Corolla, and Hilux).
*   Adds 3 types of Service function: ACC, A/C, and HV Battery.

Autel-MaxiSys-Ultra-Great-Upgrade-4
Autel-MaxiSys-Ultra-Great-Upgrade-5
Autel-MaxiSys-Ultra-Great-Upgrade-6

VW:

*   Adds diagnostic supports for models including ID.6 X 2021, ID.6 Crozz 2021, Audi Q4 e-tron 2022, and CP – Tarek 2021.
*   Updates basic functions, and special functions (including Oil Reset, EPB, and Odometer), supporting models up to 2022.
*   Adds 258 hot guided functions including Battery, Headlight Washer, and Transport Mode.
*   Adds Topology for makes including VW, Audi, Skoda, and Seat. [For MaxiSys Ultra, MaxiSys MS919 and MaxiSys MS909 only]

Autel-MaxiSys-Ultra-Great-Upgrade-7
Autel-MaxiSys-Ultra-Great-Upgrade-8

JLR:

*   Adds basic functions for 2022 PHEV models (Jaguar XE and Jaguar XF) and 2021 onward PHEV models (Discovery Sport and New Range Rover Evoque).
*   Adds 35 special functions including Power Supply Service Mode Diagnostic, Purge Valve Self Test, Fuel System Leak Check (DMTL), and Fuel Tank – Smoke Test for 2017 onward models.

Autel-MaxiSys-Ultra-Great-Upgrade-9
Autel-MaxiSys-Ultra-Great-Upgrade-10

Nissan:

* 新增2021年23款(包括Kicks、Versa、Infiniti)和2022年10款(包括Armada、Pathfinder、Frontier)的基本功能。
* 为 DTC 增加 1310 项特殊功能,包括 P0440 / P1440 - EVAP(小泄漏)、P1274 - 空燃比传感器 1 和 P0134 - 加热氧传感器 (HO2S) 1。
* 增加热特殊功能:HV 电池。支持锂离子电池容量平衡、清除电池逐渐容量损失、清除电池充电/放电信息数据等功能。

Autel-MaxiSys-Ultra-Great-Upgrade-11
Autel-MaxiSys-Ultra-Great-Upgrade-12
Autel-MaxiSys-Ultra-Great-Upgrade-13

宝马

* 优化基本功能,支持至2021年7月的车型。
* 增加7个热门特殊功能:运输模式、HV电池、ACC、A/C、雨/光传感器、EGR和FRM重置。
* 新增G22、G82等4种底盘机型的基本功能和特殊功能。
* 支持 2021 年 3 月前 F/G 底盘车型的 ECU 编程版本。

查看更多车型,请访问 https://www.auteltech.com/vehicle-coverage/coverage2。

请注意
以上所列新车型号也兼容 Autel MS909 和 MS919



:: بازدید از این مطلب : 161
|
امتیاز مطلب : 0
|
تعداد امتیازدهندگان : 0
|
مجموع امتیاز : 0
تاریخ انتشار : یک شنبه 17 فروردين 1401 | نظرات ()